SIDE STEPS EXTREME

• The product is designed for New Age Truck – Pick-up Models. It strengthness the off road image with its strong, sportive and robust structure.
• Strongly recommended to be combined with Extreme Front and Rear Guard.
• The product is produced with electrostatically painted 76mm. galvanized steel tube and fitting apparatus.
• Thanks to extra galvanization the product is resistant to corrosion.
• With its strong structure and special design it provides sportive and dynamic vision to the car, in addition to its step funtion it provides protection against impacts can come from side and bottom of the car.  
• It is installed from the original holes exist on the chassis of the car with monoblok laser cut fitting brackets. All fitting apparatus are galvanized and resistant to corrosion.
• Montaj ayaklarında özel kıskaç sistemi bulunmaktadır. Bu sistem sayesinde bağlantı ayaklarının araç eteklerine montajı hiçbir delme işlemi gerektirmeden yapılır.
• Fitting brackets are designed especially for each vehicle and produced by laser cut technology with monolithic iron providing strong and robust structure. All fitting brackets and apparatus are galvanized against oxidation.
• Special clamp system applied on the fitting brackets which provides extra connection of the product to the vehicle and prevents step extension in time.
• Product installation is easy and practical. It's installed on the original holes of the chassis without drilling, cutting and welding on the vehicle.
• Product provides side step protection in addition to visibility and step function due to its strong structure.
• Production is made according to ISO 9001-2008 TUEV standards

I. Disclaimer for Voyager Products

Voyager products are designed to be sold as decorative accessories, and should not be relied upon as protection for both passengers and vehicle. The buyer assumes all risk and liability whatsoever resulting from the use of said products. There are limitations to the severity of impact that the products sold herein can withstand and the products are not a substitute for safe and careful driving.

II.Care & Cleaning

• Although products are made with high quality raw materials which are designed to provide maximum weathering protections, they may be affected negatively by environmental conditions.By following regular care and maintenance it will ensure maximum. level of protection and good external appearance. Weekly periodic cleaning is recommended depending on the wether and environmental conditions.
• Dirt, exhaust waste, soil can consist of accumulated dust and a variety of contaminates that come from many sources, ranging from the wind to everyday use. These contaminates will vary greatly in their effect on appearance and corrosivity and ease of removal. While some may be easily removed by regular cleaning, others which result corrosivity and rusting may require waxing for effective removal.Wax-based polish. Periodical care offers maximum care and good outfit to prevent corrosion.
• Care and Cleaning Guidelines
• Rinse the product in order to remove the dirts and dusts stuck on the surface with warm water.
• Use a soft, dampened sponge or cloth to clean. Never use abrasive material like a bristle brush or scouring pad.
• The preferred cleaner is one that does not contain chlorine, such as acetone, methyl alcohol, and mineral spirits. Use neutral cleaner cleaners compounded from phosphates,alkalis such as liquid soaps and mild detergent.Do not allow cleaners to sit or soak on the product. Always test your cleaning solution on an inconspicuous area on the product before applying it to the entire surface. These can be used with warm water, bristle brushes, sponges, or clean cloths.
• Rinse the surface completely with water immediately after applying cleaners and than dry it by wiping with soft cloths to prevent streaking. Special care should be taken to remove any traces of cleaner from edges and joins

Warnings

• Never use petrolium based cleaning materials ( benzine, gasoline, thinner, etc.. ) on painted surfaces
• Do not use cleaners containing chloride painted surface. If used, rinse the surface immediately to prevent corrosion.
• Do not use a metal scraper or abrasive pad. Excessive abrasive rubbing should not be used since it could damage the surface.
• Cleaning hot, sun-heated surfaces should be avoided since possible chemical reactions will be highly accelerated and cleaning non-uniformity could occur.

III. Transportation & Handling

• The products should be delivered with their original packaging.Although the packages are prepared with high resistant raw materials handling and transportation of the products should be made in carefull.They should not be thrown quickly, bump to each other.
• The products should be submitted after the package has been opened and checked. If there is any bend,scracth or any of damage on the product damage report should be prepared witht the responsible person from the trasporter company and than they should be submitted.
• The damages during handling or transportation are not covered.

IV.Installation

Installation should be made according to installation manual.

Installation Cautions

• Control the connection apparatus after replacing them into the holes on chassis.
• The fitting brackets should be installed on the product body before starting the installation.
• The fitting brackets are galvanized so they are resistant to corrosion. Any operation such as painting,cutting or welding should not made on fitting brackets.
• After installation is completed all connection screws should be controlled as they were tightened securely.
• It is recommended to check and tighten the all the screws during each service control of the vehicle against the possibility of loosening the fastening screws for the product in time.